Temperature Sensors & Transmitters
TPT10 Integrated Temperature Transmitter
4–20 mA, 2-wire

TPT10 technical data
Measurement
- Range
- −200 to +600 °C, to customer specification
- Element
- Pt100, Pt1000 and similar
- Accuracy class
- 0.1 or 0.2
- Non-linearity
- 0.2
- Hysteresis
- Better than 0.01 % of span
Electrical
- Supply voltage
- DC 24 V (12–36 V)
- Output
- Two-wire 4–20 mA; three-wire 1–5 V
- Load impedance
- 750 Ω
- Insulation resistance
- ≥ 100 MΩ at 100 V DC
Mechanical
- Probe length
- To customer specification
- Probe diameter
- 8 mm standard, others to order
- Probe material
- Stainless steel
- Process connection
- G1/2″, M20×1.5 or to order
- Ambient temperature
- −20 to +60 °C
- Ambient humidity
- < 85 %
- Ingress protection
- IP65
Values are for the standard configuration. Ranges, threads, probe lengths and output types outside this table are available on request — the datasheet revision for a custom build is issued with the quotation.
Request the PDF datasheet →Temperature Sensors & Transmitters
TPT10Integrated Temperature Transmitter
4–20 mA, 2-wire
Pt100 probe with an integrated transmitter in the head, giving a two-wire 4–20 mA signal directly from the sensor. −200 to +600 °C, 0.1 or 0.2 accuracy class, epoxy-potted and intrinsically safe module, IP65.
Engineering reply · Evaluation samples available · Custom ranges built to order
- Two-wire 4–20 mA straight from the head — no long RTD leads
- Epoxy-potted: vibration and humidity resistant
- Intrinsically safe transmitter module
- Accuracy class 0.1 or 0.2
- Reverse-polarity and short-circuit protection
How it works
The TPT10 puts the transmitter on the probe rather than in the panel. The element's resistance is linearised, protected against supply reversal, and converted to a two-wire 4–20 mA current in the head, so the cable run carries a signal that does not pick up resistance error from long leads. The module is epoxy-potted, which is what makes it survive vibration and humidity in a plant room, and it is an intrinsically safe design for hazardous areas. Accuracy class is 0.1 or 0.2, and the probe length is made to your requirement.
Typical applications
- Long cable runs where RTD lead resistance would matter
- Hazardous areas needing an intrinsically safe loop
- Retrofit of bare RTD probes without a panel transmitter
Not certain TPT10 is the right unit?
Send the medium, range, process connection and the signal your control system accepts. We will confirm the model — or tell you which one fits better — before you commit to an order.
Same family
Other temperature instruments

Temperature Transmitter
Local display
Integrated temperature transmitter with a local display in the head, so the temperature is readable at the measurement point. −200 to +600 °C, two-wire 4–20 mA, 0.1 or 0.2 accuracy class, epoxy-potted, IP65.
View specifications
Smart Temperature Transmitter
MCU, 2 alarm outputs
Microcontroller-based temperature transmitter with a wide −200 to +600 °C span, 0.1 or 0.2 accuracy class, local display and two opto-isolated alarm outputs. 4–20 mA or 1–5 V, 750 Ω load, IP65.
View specifications
Temperature Transmitter Controller
4 relays, 2088 housing
Temperature transmitter and controller in the standard 2088 housing: 24-bit A/D, bright LED display, four relays and 4–20 mA / 1–5 V output. −200 to +600 °C, 0.1 or 0.2 accuracy class, IP65.
View specifications
Temperature Transmitter Controller
5 relays, RS485
Five relay outputs plus RS485 Modbus on a Pt100/Pt1000 temperature transmitter. −200 to +600 °C, 24-bit A/D, LED display, parallel analogue output, IP65. For temperature control with supervisory reporting.
View specifications